White-membrane flat roof specialists for Hudson County homes and commercial buildings

TPO Roof Leak Repair in union city that stops the leak for good

When a TPO Roof Leak Repair in union city is what your building needs, you want a crew that reads membrane seams like a map. We handle thermoplastic roof leak repair union city NJ property owners rely on, from Bergenline Avenue storefronts to Troy Towers-area rooftops. We find the source, seal it, and test it before we pack up.

Union City Roof Rescue — roof leak repair union city nj you can rely on
Careful work. Honest options.
About this service

What TPO Roof Leak Repair in union city actually involves

TPO Roof Leak Repair in union city is the process of locating and sealing water intrusion in a single-ply thermoplastic polyolefin membrane roof, then restoring the membrane so it sheds water again. TPO is a heat-welded white sheet, so leaks usually start where the welds, flashings, or penetrations fail rather than in the field of the sheet itself. We scan the roof, trace the water back to its entry point, and repair the membrane with heat-welded patches, not caulk-and-hope smears.

Union City's flat-roof building stock takes a beating. Freeze-thaw cycles in January crack seams, summer heat pushes ponding water against parapet walls, and a clogged gutter overflow sends water straight into a ceiling. If you have been searching for TPO roof leak repair near me union city, we handle thermoplastic roof leak repair union city NJ 07087 calls every week. We are based here, we know these roofs, and we get to you fast.

  • ✓ Stop ceiling damage cold
  • ✓ Heat-welded, not patched over
  • ✓ Protect the whole flat roof
  • ✓ Keep tenants and staff dry
What's included

What our TPO Roof Leak Repair includes

Every TPO repair we do in Union City starts with a real diagnosis and ends with a water test. Here is what is covered in a standard repair visit, so you know what you are paying for before we climb the ladder.

01
✓

Full leak detection scan

We walk the roof with a moisture meter and infrared thermal camera to find the entry point and map how far water has spread under the membrane. On larger flat roofs we add a drone pass to cover the field quickly.

02
✓

Heat-welded membrane repair

We cut back the failed TPO, dry the substrate, and heat-weld a new patch or flashing detail to manufacturer spec. No caulk-only patches that fail in a season.

03
✓

Flashing and boot reseal

Pipe boots, parapet terminations, and curb flashing get rebuilt with welded membrane collars. These are the spots where most TPO leaks start, so we do not skip them.

04
✓

Water test before we leave

We flood-test or hose-test the repair and watch for any weep. If the fix does not hold, we keep working until it does. You see the test before we pack up.

05
✓

Photo documentation

You get before-and-after photos of the repair and a written summary of what we found. That documentation keeps your manufacturer membrane warranty intact and gives you a record for your files.

06
✓

Debris cleanup and magnet sweep

We haul away old membrane and run a magnet sweep for dropped screws and nails. Your roof and driveway are left clean, not littered with roofing debris.

How it works

How our TPO leak repair process runs

You call (551) 348-9609 and describe the leak. We ask where the stain is, how long it has been there, and whether the roof is flat TPO. That tells us whether to send an emergency crew tonight or schedule a same-day inspection. Most calls get a visit within 24 hours.

We walk the roof with a moisture meter and an infrared thermal camera to find wet insulation under the membrane. On larger flat roofs we fly a roof inspection drone to cover the field fast. This is how we trace the water to its real entry point instead of guessing.

We show you photos of the failed seam, flashing, or pipe boot and explain the fix in plain terms. You get a written price before we start. No surprise line items, no pressure to replace a roof that just needs a repair.

We cut back the damaged membrane, dry the substrate, and heat-weld a new TPO patch or flashing detail. Pipe boots, roof flashing, and parapet terminations get the same treatment. A typical repair takes 2 to 4 hours depending on access.

Before we leave, we flood-test or hose-test the repair and watch for any weep. We magnet-sweep for dropped screws, haul away old membrane, and walk you through what we found. If we see a second weak spot, we tell you now, not after the next storm.

TPO Roof Leak Repair
STEP 01Call and triage

You call (551) 348-9609 and describe the leak. We ask where the stain is, how long it has been there, and whether the roof is flat TPO. That tells us whether to send an emergency crew tonight or schedule a same-day inspection. Most calls get a visit within 24 hours.

Tools & methods

Tools and methods we use on TPO roofs

01
✓

Infrared thermal camera

Reads temperature differences to find wet insulation hidden under a dry-looking TPO membrane, so we map the leak without tearing up the whole roof.

02
✓

Moisture meter

Confirms wet substrate and insulation at the suspected leak point. It tells us how far to cut back the membrane before we weld a patch.

03
✓

Roof inspection drone

Covers large flat roofs fast and gives us a clear view of seams and flashing we cannot safely reach on foot. We use it on commercial buildings across Union City.

04
✓

Heat welder

Bonds TPO membrane patches and flashing details to the existing sheet at the correct temperature. A proper weld is what makes a TPO repair permanent.

05
✓

Extension ladder and safety harness

Gets us safely onto flat roofs and keeps our technicians tied off while they work. Safety gear is not optional on a multi-story Union City building.

06
✓

Caulking gun and TPO sealant

Finishes edge details and terminations where a weld alone will not seal. We use manufacturer-approved sealant compatible with the membrane.

Real results

Before and after.

Bergenline Avenue storefront seam leak
TPO Roof Leak Repair

Bergenline Avenue storefront seam leak

A retail building had water dripping onto the sales floor every storm. Two prior caulk patches had failed, and the ceiling tiles were stained and sagging over a 10-foot section.

After: We traced the leak to a failed heat-welded seam, cut it back, and welded a new TPO strip. A water test held with no weep. The ceiling stayed dry through the next three storms.

Book this service →
Troy Towers pipe boot failure
TPO Roof Leak Repair

Troy Towers pipe boot failure

A cracked pipe boot was sending water down a vent pipe into a tenant's bathroom. The leak had been active for weeks and had stained the ceiling and warped the vanity cabinet.

After: We replaced the boot with a heat-welded membrane collar and water-tested the penetration. The leak stopped the same day, and the tenant's ceiling dried out without further damage.

Book this service →
48th Street parapet flashing rebuild
TPO Roof Leak Repair

48th Street parapet flashing rebuild

Ponding water against a parapet wall had worked behind the flashing and soaked the insulation. The homeowner saw a ceiling stain that kept growing after every rain.

After: We rebuilt the flashing with welded membrane, replaced the wet insulation, and corrected the drainage so water moved off the roof. The ceiling stain stopped spreading within a week.

Book this service →
Problems we solve

TPO roof problems we solve in union city

Most TPO leaks trace back to a handful of failure points. Here are the ones we fix most often on Union City flat roofs, and what happens if you let them go.

Ask a pro →
01

Failed heat-welded seams opening up

We cut back the failed seam, dry the area, and re-weld a new TPO strip over the joint. A seam repair is quick and permanent when it is welded to spec, and we test it with water before we leave.

↗
02

Pipe boot failure at plumbing vents

We replace the failed boot with a heat-welded membrane collar built for the pipe size. That repair outlasts a rubber boot by years and keeps the penetration watertight.

↗
03

Ponding water against parapet walls

We repair the flashing and check the drainage so water moves off the roof. If a low spot is holding water, we tell you what it takes to correct it and stop the cycle.

↗
04

Clogged gutter overflow backing under the edge

We clear the blockage, repair the gutter, and reseal the membrane edge termination. Fixing the drainage and the edge together stops the leak at its source.

↗
Proof you can check

Licensed, insured, and accountable

  • NJ Home Improvement Contractor (HIC) License · New Jersey Division of Consumer Affairs
  • NJ Roofing Contractor License · State of New Jersey
  • OSHA Safety Certification · Occupational Safety and Health Administration
  • EPA Lead-Safe Certified Firm · U.S. Environmental Protection Agency
  • NRCA Member · National Roofing Contractors Association
Customer reviews

What Union City customers say

★★★★★
“Water was dripping through my kitchen ceiling every time it rained. The crew found a failed seam on my TPO flat roof that two other guys missed. They heat-welded a patch, tested it with a hose, and I have not seen a drop since. Took about three hours and the price was exactly what they quoted.”
MG

Maria G.Homeowner, Downtown Union City

✓ Verified
★★★★★
“A pipe boot on my flat roof cracked and started leaking into a tenant's bathroom. They replaced the boot with a welded membrane collar instead of slapping caulk on it. That was last fall and it has held through every storm since. Fair price and no upsell on a whole new roof.”
AP

Anthony P.Landlord, Troy Towers Area

✓ Verified
Good questions

Frequently Asked Questions

(551) 348-9609

Most TPO leak repairs in Union City run $350 to $1,200 in 2026, depending on how far the water traveled and how much membrane has to be cut back. A simple pipe boot or seam repair sits at the low end, while a parapet flashing rebuild with wet insulation replacement lands higher. We give you the number before we start.

We find the entry point with a moisture meter and infrared thermal camera, cut back the failed membrane, dry the substrate, and heat-weld a new TPO patch or flashing detail into place. We finish with a water test. The whole job usually takes 2 to 4 hours, and we do not leave until the repair holds.

Yes, most TPO leaks can be patched rather than requiring a full membrane replacement. Heat-welded patches on seams, pipe boots, and flashing failures are permanent repairs when done to manufacturer spec. We only recommend replacement when the membrane is brittle across the whole roof or wet insulation covers a large area.

Union City Roof Rescue fixes TPO roof leaks across Hudson County, including 07087 and the neighborhoods around 48th Street, Bergenline Avenue, and the Troy Towers area. Call (551) 348-9609 and we will schedule a same-day inspection or an emergency visit if the leak is active right now.

Ready when you are

Get your TPO Roof Leak Repair in union city scheduled today

A leaking TPO membrane only gets worse with the next rain. Call Union City Roof Rescue at (551) 348-9609 and we will trace the leak, give you a written price, and seal it right. Same-day and 24/7 emergency service across Hudson County.

Book a Repair (551) 348-9609 →
Request an appointment

Call Union City Roof Rescue

Call us at (551) 348-9609 or email info@unioncityroofrescue.com. We answer the phone 24/7 for active leaks and schedule standard inspections Monday through Friday. If you leave a message after hours, we call back within the hour.

↗
Emergency?Call now