Licensed, insured, and on your roof the same day you call

Chimney flashing repair union city NJ that stops the leak

When water shows up on the ceiling beside your chimney, you need chimney flashing repair union city NJ homeowners actually trust. We pull the old rusted flashing, rebuild the seal with new metal and ice and water shield, and water-test it before we pack up. Most chimney leak repair in union city NJ jobs are done in a single visit, with a written warranty on the work.

Chimney Flashing Repair you can count on
Careful work. Honest options.
About this service

Chimney flashing repair union city NJ done to code

Chimney flashing repair union city NJ is the trade of replacing or resealing the metal that ties your chimney to the roof plane, so rain and snowmelt run around the stack instead of into it. Flashing fails in predictable ways: rust eats through the base metal, tar patches crack, step flashing pulls away from the brick, and counterflashing lifts after a hard freeze. We remove the failed layers, cut new metal to fit, and tie it back into the shingles and underlayment so the joint sheds water the way it was engineered to.

Union City roofs take a beating from both directions. Bergenline Avenue and Summit Avenue have dense blocks of century-old brick buildings where the chimney mortar is already soft and the flashing is original. Add nor'easters off the Hudson, freeze-thaw cycles that open seams every February, and summer storms that dump two inches in an hour, and a small flashing leak turns into a ceiling stain fast. If you have been searching chimney leak repair union city NJ 07087, the fix is almost always the flashing, not the brick.

  • ✓ Leak stopped at the source
  • ✓ Same-day and 24/7 response
  • ✓ Work warrantied in writing
  • ✓ Code-correct, inspection-ready
What's included

What our chimney flashing repair includes

Every chimney flashing repair we do covers the full joint, not just the visible crack. Here is what is included in a standard repair, and what we handle as an add-on when the job calls for it.

01
✓

Full leak diagnosis

We inspect the roof and attic and scan the ceiling below with a moisture meter and infrared thermal camera. You get a clear explanation of what failed and why, so you understand the repair before we start.

02
✓

Removal of failed flashing

We strip the old rusted metal, cracked tar, and failed sealant down to sound material. Leaving old flashing in place is why so many chimney repairs fail within a year, so we take it out and start clean.

03
✓

New metal and underlayment

We cut and fit new step flashing, counterflashing, and chimney pan, set over ice and water shield. The metal is sized to your chimney and roof pitch, and every piece is fastened and sealed the way the system requires.

04
✓

Sealing and tie-in

We tie the new flashing into the surrounding shingles, membrane, or tile, and seal every joint with quality sealant. The finished joint sheds water around the chimney instead of letting it run behind the flashing.

05
✓

Water test and warranty

We run water at the chimney and watch the joint and the ceiling below until we confirm it is dry. Then we hand you photos of the finished work and a written workmanship warranty on the repair.

How it works

How our chimney flashing repair process works

You call (201) 555-0147 or book online and tell us what you are seeing: a stain on the ceiling, water running down the chimney breast, or a drip in the attic. We ask a few quick questions to size up the job, give you an honest ballpark over the phone, and lock in a same-day or next-day window that fits your schedule.

A technician goes up on the roof and, when accessible, into the attic. We check the step flashing, counterflashing, chimney pan, and the shingles around the stack, and we scan the ceiling below with an infrared thermal camera to confirm the water path. This usually takes 30 to 45 minutes and tells us whether the leak is the flashing or something else.

Before any metal comes off, you get a clear price for the repair. We explain what failed, what we are replacing, and what it costs. No pressure, no add-ons you did not ask for. If the job is bigger than expected, you hear it from us first, not from the invoice.

We strip the failed flashing, cut and fit new metal, set it over ice and water shield, and tie it into the shingles and underlayment. Step flashing goes in course by course, counterflashing gets set into the mortar or fastened to the brick, and every seam gets the right sealant. A standard chimney flashing repair runs two to four hours.

Before we leave, we run water at the chimney and watch the joint and the ceiling below. If it is dry, we clean up, haul away the old metal, and hand you photos of the finished work plus your written warranty. If anything still shows moisture, we stay on it until it is dry.

Chimney Flashing Repair
STEP 01Call and schedule

You call (201) 555-0147 or book online and tell us what you are seeing: a stain on the ceiling, water running down the chimney breast, or a drip in the attic. We ask a few quick questions to size up the job, give you an honest ballpark over the phone, and lock in a same-day or next-day window that fits your schedule.

Tools & methods

Tools and methods we use

01
✓

Infrared thermal camera

Shows us moisture trapped under the roof surface and in the ceiling below, so we can confirm the water path without tearing anything open.

02
✓

Moisture meter

Reads the actual moisture content in drywall, framing, and roof decking, confirming whether a stain is active and whether the repair is dry.

03
✓

Roof inspection drone

Lets us inspect steep or hard-to-reach chimney flashing safely and quickly, and gives you clear photos of what we find up there.

04
✓

Pitch hoist

Lifts flashing materials and tools onto steep roofs safely, so the crew can work efficiently without risking a fall or damaging the roof.

05
✓

Caulking gun and quality sealant

Applies the right sealant to each joint. We use sealants matched to the metal and the roof material, not a one-size-fits-all tube.

06
✓

Pry bar and utility knife

Let us lift shingles and cut flashing cleanly, so the new metal ties in without tearing the surrounding roof apart.

Real results

Before and after.

Bergenline Avenue chimney leak stopped
Chimney Flashing Repair

Bergenline Avenue chimney leak stopped

A homeowner on Bergenline Avenue had a spreading ceiling stain every time it rained. The step flashing had rusted through and pulled away from the brick, and a previous tar patch had cracked. Water was running behind the flashing and into the attic.

After: We stripped the old flashing and tar, installed new step flashing and counterflashing over ice and water shield, and water-tested the joint. The ceiling stayed dry through the next three storms, and the repair carried a written workmanship warranty.

Book this service →
48th Street ice dam flashing repair
Chimney Flashing Repair

48th Street ice dam flashing repair

After a February freeze, a landlord on 48th Street had water coming into a top-floor unit around the chimney. An ice dam had forced water under the flashing, and the counterflashing had lifted. The tenant was threatening to withhold rent.

After: We removed the ice dam, rebuilt the counterflashing and step flashing, and improved the attic ventilation to reduce future ice dams. The unit stayed dry, and the landlord had photos and a warranty to show the tenant.

Book this service →
Union City Heights counterflashing rebuild
Chimney Flashing Repair

Union City Heights counterflashing rebuild

A homeowner on Union City Heights had been quoted a full roof replacement by two other roofers because of a chimney leak. The actual problem was failed counterflashing and a rusted pan, not the whole roof. The leak had stained the ceiling and was getting worse.

After: We replaced the counterflashing and built a new chimney pan over ice and water shield, tied it into the existing shingles, and water-tested it. The leak stopped for a fraction of a roof replacement, and the ceiling stain stopped spreading.

Book this service →
Problems we solve

Chimney leak problems we fix in Union City

Most chimney leaks trace back to one of a handful of failures. Here are the ones we see most often on Union City roofs and what we do about them.

Ask a pro →
01

Rusted or missing step flashing

We remove the failed step flashing, install new metal woven into the shingle courses, and set it over ice and water shield. The joint is rebuilt to shed water the way it was designed to, and we water-test it before we leave.

↗
02

Lifted or cracked counterflashing

We reset or replace the counterflashing, set it into the mortar or fasten it to the brick, and seal the joint correctly. This is one of the most common causes of chimney leak repair calls in Union City, and it is usually a same-day fix.

↗
03

Rusted-through chimney pan

We build and install a new pan sized to your chimney, set over ice and water shield, and tie it into the surrounding flashing. The new pan is heavier-gauge metal, so it lasts far longer than the original.

↗
04

Failed tar patches from past repairs

We strip the old tar, find the actual failure point, and rebuild the flashing with new metal and proper underlayment. No more patching over a patch. The repair is done once, correctly, and warrantied in writing.

↗
Proof you can check

Licensed, insured, and warrantied

  • NJ Home Improvement Contractor (HIC) License · New Jersey Division of Consumer Affairs
  • GAF Master Elite Contractor · GAF
  • Owens Corning Preferred Contractor · Owens Corning
  • EPA Lead-Safe Certified Firm · U.S. Environmental Protection Agency
  • NRCA Member · National Roofing Contractors Association
Customer reviews

What Union City customers say

★★★★★
“We had a brown stain spreading on the ceiling next to the chimney every time it rained. Union City Roof Rescue came out the same day, found the step flashing had pulled away, and rebuilt it with new metal. Two hours of work and it has been bone dry through two storms since. Fair price and they cleaned up after themselves.”
MG

Maria G.Homeowner, Bergenline Avenue

✓ Verified
★★★★★
“Two other roofers wanted to sell me a whole new roof because of a chimney leak. Union City Roof Rescue actually diagnosed it, showed me the failed counterflashing, and fixed just that. Cost a fraction of what I was quoted elsewhere and the leak is gone. I will use them for everything from now on.”
PS

Priya S.Homeowner, Union City Heights

✓ Verified
Good questions

Frequently asked questions about chimney flashing repair

(201) 555-0147 →

Most chimney flashing repairs in Union City run $350 to $900 in 2026, depending on roof pitch, chimney size, and how much metal has to be replaced. A simple reseal of step flashing sits at the low end; a full rebuild with new pan and counterflashing sits higher. We give you the exact price before we start, so there are no surprises.

We start by finding the entry point with a moisture meter and infrared thermal camera, then strip the failed flashing and rebuild the joint with new metal over ice and water shield. Step flashing goes in course by course, counterflashing gets set into the brick or mortar, and we water-test the finished work before we leave. Most jobs take two to four hours.

Union City Roof Rescue repairs chimney flashing across Union City and Hudson County, from Bergenline Avenue to the North Bergen border. We are a licensed New Jersey home improvement contractor, insured and bonded, and we run same-day and 24/7 emergency service. Call (201) 555-0147 and we will get a technician on your roof.

Yes, in most cases the flashing is exactly what is leaking. Water gets in where the step flashing has pulled away, where counterflashing has lifted, or where the pan has rusted through. Once we rebuild those joints with new metal and proper underlayment, the leak around the chimney stops. If the leak turns out to be elsewhere, we tell you and fix that instead.

Ready when you are

Get your chimney flashing repair union city NJ today

Water around the chimney only gets worse. Call Union City Roof Rescue at (201) 555-0147 and we will diagnose the leak, give you a straight price, and repair the flashing, often the same day. Licensed, insured, and warrantied in writing.

Book a repair (201) 555-0147 →
Request an appointment

Call Union City Roof Rescue

Call us at (201) 555-0147 or email info@unioncityroofrescue.com. We answer the phone 24/7 for active leaks and schedule standard inspections Monday through Friday. If you leave a message after hours, we call back within the hour.

↗
Emergency?Call now