Infrared roof leak detection union city NJ uses a thermal camera to pinpoint hidden water intrusion without tearing your roof apart. If you have a ceiling water stain, a flashing leak, or a flat roof that ponds after every storm, our thermal imaging roof leak detection service union city, New Jersey team finds the source in one visit. We serve homeowners and building owners across Hudson County with same-day scheduling and honest, upfront pricing.
Infrared Roof Leak Detection union city NJ Explained
Infrared roof leak detection union city NJ is a diagnostic service that uses a thermal camera to read temperature differences across your roof surface and locate trapped moisture you cannot see. Wet insulation and saturated roof underlayment hold heat differently than dry material, so the camera shows dark or light patches that map exactly where water is sitting. We pair that scan with a moisture meter to confirm readings, then trace the leak back to its entry point, whether that is a pipe boot failure, a roof valley leak, or a flashing leak at a chimney.
Union City roofs take a beating. Tight lot lines, brick multifamily buildings, and a mix of flat and pitched roofs mean water travels sideways before it ever shows up on your ceiling. A thermal roof leak inspection union city catches that hidden path before it rots decking or blows out a ceiling. If you have been searching for infrared roof leak detection near me union city, we schedule same-day scans and cover every ZIP in the 07087 service area.
Every scan is a full diagnostic, not just a camera pass. You get the thermal images, the moisture verification, and a written plan you can act on. Here is what is covered in a standard visit, and what we can add on if your situation calls for it.
01
✓
Full Roof and Attic Survey
We walk the roof and inspect the attic or ceiling cavity by eye before scanning. That means checking flashing, pipe boots, roof valley metal, and membrane seams, plus looking for ceiling water stains and sagging decking inside.
02
✓
Infrared Thermal Camera Scan
We scan the full roof surface with an infrared thermal camera in a grid pattern, plus the interior ceiling plane where accessible. On flat roofs we scan every 4 to 6 feet to make sure no wet zone is missed.
03
✓
Moisture Meter Verification
Every thermal anomaly gets a moisture meter reading to confirm it is real moisture and not a reflection or shadow. We record the percentage and mark the zone with chalk so you can see it yourself.
04
✓
Written Findings Report
You get a written summary with timestamped thermal images, moisture percentages, a labeled roof diagram, and the suspected entry point. It is formatted so you can hand it to an insurance adjuster or a property manager.
05
✓
Same-Day Repair Scope
If the leak is a simple flashing, pipe boot, or seam repair, we can often fix it the same visit. If it needs a larger repair, you get a written scope with pricing so you can decide without pressure.
06
✓
Maintenance Recommendations
We tell you what to watch and when to re-scan. For flat roofs, that usually means an annual scan in spring and a gutter check before winter. For pitched roofs, it means checking flashing and boots after every major storm.
How it works
How Our Infrared Leak Detection Process Works
We ask where the stain is, when it shows up, and whether it gets worse after rain or after the sun hits. That tells us whether to scan in the morning when the roof is warming or in the evening when it is cooling. Most calls take under 10 minutes, and we book a same-day or next-morning window.
A technician walks the roof with an extension ladder and safety harness, checking flashing, pipe boots, and membrane seams by eye first. Inside, we check the attic or ceiling cavity for staining, sagging decking, and wet insulation. This walk-through takes 20 to 30 minutes and sets up the thermal scan.
We run the infrared thermal camera across the roof surface and the interior ceiling plane, looking for temperature anomalies that signal trapped moisture. On flat roofs we scan in a grid pattern every 4 to 6 feet. The scan itself runs 30 to 60 minutes depending on roof size and how many levels we need to cover.
Every hot spot gets a moisture meter reading to confirm the thermal image is real and not a reflection or a shadow. We record the percentage, mark the zone with chalk, and photograph each location. This is the step that separates a real diagnosis from a camera that just shows pretty colors.
You get a written summary with photos, moisture readings, and the suspected entry point, plus a repair scope with pricing. If it is a simple pipe boot or flashing reseal, we can often fix it the same day. If it needs a larger repair, you have the documentation to decide and to file a claim.
STEP 01Phone Intake
We ask where the stain is, when it shows up, and whether it gets worse after rain or after the sun hits. That tells us whether to scan in the morning when the roof is warming or in the evening when it is cooling. Most calls take under 10 minutes, and we book a same-day or next-morning window.
Tools & methods
Tools and Methods We Use
01
✓
Infrared Thermal Camera
Reads temperature differences across the roof surface to locate trapped moisture. We use it on both the exterior roof and the interior ceiling plane.
02
✓
Moisture Meter
Confirms every thermal anomaly is real moisture, not a reflection or shadow. We record the percentage at each location.
03
✓
Roof Inspection Drone
Used for steep or high roofs where walking is unsafe. It captures high-resolution images of flashing, valleys, and penetrations.
04
✓
Extension Ladder and Safety Harness
Standard access equipment for roof walks. Every technician is OSHA Safety Certification trained on fall protection.
05
✓
Caulking Gun and Sealant
For same-day repairs of minor flashing and penetration leaks found during the scan. We use manufacturer-approved sealants.
06
✓
Pry Bar and Utility Knife
For opening up small sections to inspect underlayment and decking when the thermal image shows saturation.
Real results
Before and after.
Infrared Roof Leak Detection
Ceiling Stain Traced to Pipe Boot
A homeowner on 48th Street had a ceiling stain that kept returning after every rain. Two previous roofers had replaced shingles above the stain with no result. The leak had been active for months, and the drywall was starting to sag.
After: Our thermal scan found the actual source: a failed pipe boot about 12 feet from the stain. We replaced the boot, resealed the penetration, and confirmed with a moisture meter that the area was dry. Total repair time was under two hours.
A six-unit building on Bergenline Avenue had a flat roof that ponded after every storm. The property manager had been told the whole roof needed replacement. Tenant complaints about ceiling drips were coming in weekly.
After: Thermal scanning showed the moisture was confined to two sections of saturated insulation near the drains. We replaced only those sections, repaired the failed seams, and corrected the low spots. The repair cost about 20% of a full tear-off.
After last winter, a homeowner in Union City Heights noticed water coming in around the chimney. The ice dam had forced water under the shingles and behind the flashing. By the time the stain appeared, the damage had been developing for weeks.
After: We scanned the roof edge and chimney area, confirmed the moisture path with a meter, and repaired the flashing plus the damaged underlayment. We added ice and water shield at the eaves and improved attic ventilation to prevent a repeat.
Most leaks we find in Union City fall into a handful of categories. Thermal imaging finds them all, even when the water shows up far from the actual entry point.
We scan the full roof and ceiling plane to find the actual entry point, confirm it with a moisture meter, and repair the source. Then we verify with a second scan that no moisture remains in the assembly.
↗02
Flat roof ponding after every storm
We scan the ponding areas to see how far the moisture has spread, then repair the low spots and failed seams. If the insulation is saturated, we replace only the affected sections instead of the whole roof.
↗03
Chimney or skylight leak that no one can find
Thermal imaging traces the water path from the stain back to the entry point. We repair the chimney flashing or skylight curb and reseal with proper materials, then confirm with a moisture meter.
↗04
Ice dam damage from last winter
We scan the eaves and roof edge for trapped moisture, repair any damaged underlayment and flashing, and recommend ice and water shield plus attic ventilation improvements to prevent a repeat.
↗
Proof you can check
Licensed, Insured, and Documented
NJ Home Improvement Contractor (HIC) License · New Jersey Division of Consumer Affairs
OSHA Safety Certification · Occupational Safety and Health Administration
EPA Lead-Safe Certified Firm · U.S. Environmental Protection Agency
GAF Master Elite · GAF Materials Corporation
NRCA Member · National Roofing Contractors Association
Customer reviews
What Union City Customers Say
★★★★★
“We had a ceiling stain that kept coming back after every rain. Two other roofers told us we needed a full tear-off. Union City Roof Rescue ran a thermal scan and found the leak was a failed pipe boot about 12 feet from the stain. They fixed it in an hour and the stain has not come back.”
MR
Maria R.Homeowner, Downtown Union City
✓ Verified
“
★★★★★
“We manage a six-unit building with a flat roof that had been leaking for months. The thermal scan showed exactly which sections of insulation were saturated, and they gave us a report we used for the insurance claim. Repair was done in two days with no disruption to tenants.”
AD
Anthony D.Building Manager, Bergenline Avenue
✓ Verified
★★★★★
“After the ice dams last winter we had water coming in around the chimney. They scanned the roof, showed us the thermal images on a tablet, and explained exactly where the water was getting in. Fixed the flashing and added ice and water shield. Honest pricing, no upsell.”
Most residential scans run $350 to $650 in 2026, and larger commercial or multifamily roofs run $650 to $1,200 depending on square footage and roof levels. The price includes the thermal scan, moisture meter verification, and a written report with photos. If we do the repair, we credit a portion of the scan fee toward the work.
Wet insulation and saturated roof underlayment hold heat differently than dry material. Our infrared thermal camera reads those temperature differences and shows dark or light patches where moisture is trapped. We then confirm each spot with a moisture meter, so you get a verified location, not just a color on a screen.
We do. Union City Roof Rescue runs thermal scans across Hudson County, including Downtown Union City, Bergenline Avenue, Summit Avenue, Union City Heights, and the North Bergen and West New York borders. Call (201) 555-0147 and we can usually schedule a same-day or next-morning visit.
Yes, when it is done with the right conditions and confirmed with a moisture meter. Accuracy depends on temperature differential, so we scan when the roof is warming or cooling, not at a flat midday temperature. Every thermal image we take is verified with a meter reading before we call it a leak.
Book Infrared Roof Leak Detection union city NJ Today
Stop guessing where the water is coming from. Call (201) 555-0147 and we will schedule a thermal scan, confirm the source with a moisture meter, and give you a written repair plan. Same-day and emergency slots available across Hudson County.
Call us at (201) 555-0147 or email info@unioncityroofrescue.com. We answer the phone 24/7 for active leaks and schedule standard inspections Monday through Friday. If you leave a message after hours, we call back within the hour.