Full roof inspection
We walk the entire roof, not just the area above the stain. We check seams, flashing, drains, pipe boots, and parapet walls, and we take moisture meter readings across the deck to find hidden wet spots.
Flat Roof Leak Repair in union city means finding the actual breach in your EPDM, TPO, or modified bitumen membrane and sealing it before the next storm pushes water into your ceiling. We handle flat roofing repair union city, New Jersey homeowners and building owners call about every week: ponding water, seam separation, flashing failures, and pipe boot leaks. We inspect, we diagnose, we fix it, and we test it before we leave.

Flat Roof Leak Repair in union city is the process of locating water intrusion on a low slope or flat roof and restoring the waterproof layer without tearing off the whole assembly. On a flat roof, water does not run off the way it does on a pitched shingle roof. It sits, it creeps sideways under seams, and it finds the lowest point inside your building. That is why a ceiling stain above your kitchen in Union City Heights often traces back to a seam 20 feet away near a rooftop unit. We start with a moisture meter and an infrared thermal camera to map wet insulation, then confirm the entry point with a hose test.
Most flat roofs in Hudson County are 10 to 40 years old, and the failures we see follow a pattern: seam separation on EPDM, brittle flashing at the parapet wall, and ponding water that never drains after rain. If you own a two-family on Bergenline Avenue or a commercial building near Palisade Avenue, a small membrane breach can soak insulation for months before you notice a stain. That is why we treat every flat roof leak fixing union city call as urgent, not cosmetic. We also document what we find so you can decide between a targeted repair and a full replacement.
Every flat roof leak repair includes a full inspection, diagnosis, the repair itself, and a water test before we leave. We tell you upfront what is covered in the base price and what would be an add-on, like insulation replacement or a full membrane section, so there are no surprises on the invoice.
We walk the entire roof, not just the area above the stain. We check seams, flashing, drains, pipe boots, and parapet walls, and we take moisture meter readings across the deck to find hidden wet spots.
An infrared thermal camera scan shows us where water has traveled under the membrane. This is how we find the actual entry point instead of guessing based on where the ceiling stain is.
We cut back the damaged material and install a compatible patch or new membrane section. EPDM gets splice adhesive, TPO gets heat-welded, modified bitumen gets torch or cold-applied membrane. The repair matches your existing roof system.
Most flat roof leaks start at a penetration or edge. We reseal or replace flashing at parapet walls, pipe boots, vents, and drains as part of the repair so the whole area is watertight, not just the visible breach.
We hose-test or flood-test the repair and watch for any sign of movement. Then we photograph the work and give you a summary of what was done, what materials were used, and what to watch for going forward.
You call (551) 348-9609 or book online. We ask what you are seeing, where the stain is, and how long it has been there. For an active leak, we prioritize same-day or next-morning scheduling. You get a two-hour arrival window, and we call when we are on the way.
A technician sets an extension ladder, ties off with a safety harness, and walks the roof. We check seams, flashing, pipe boots, drains, and the parapet wall. We take moisture meter readings across the deck and run an infrared thermal camera scan to find wet insulation that is not visible from the surface.
We show you photos of the failure point and explain what caused it. You get a written scope with a fixed price: what we will repair, what materials we will use, and how long it will take. Most single-point repairs take two to four hours. Larger membrane sections can take a full day.
We cut back damaged membrane, dry the deck where needed, and install the repair using compatible materials. That might mean a modified bitumen patch, a TPO heat-welded seam, or new flashing and roof cement at a parapet. Every layer gets installed to manufacturer spec so the repair does not void your existing warranty.
We flood-test or hose-test the repair area and watch for any sign of movement. Then we walk you through what we did, show you the photos, and give you a maintenance note for the season. If we see a second weak point nearby, we point it out now rather than waiting for it to fail.
You call (551) 348-9609 or book online. We ask what you are seeing, where the stain is, and how long it has been there. For an active leak, we prioritize same-day or next-morning scheduling. You get a two-hour arrival window, and we call when we are on the way.
Detects temperature differences caused by wet insulation under the membrane, revealing hidden moisture that a visual inspection cannot see.
Confirms the presence and extent of moisture in the roof deck and insulation so we know exactly how far the damage reaches.
Surveys large commercial roofs quickly, capturing high-resolution images and flagging suspect areas before we climb up.
Provides safe roof access on Union City's narrow lots and varied building heights, with full fall protection for every technician.
Applies sealant and Henry Company roof cement at flashing details, terminations, and small penetrations where a precise bead is needed.
Cuts back damaged membrane and lifts flashing so we can inspect the substrate and install the repair correctly.

A slow leak around the plumbing stack had been staining the bathroom ceiling for months. The pipe boot was cracked and brittle from UV exposure, and water was running down the stack into the insulation.
After: We replaced the pipe boot with a new UV-resistant collar, sealed it to the membrane, and water-tested the area. The ceiling stain stopped spreading within one rain cycle, and the moisture meter reading returned to dry.
Book this service →
A 4,000-square-foot TPO roof had two clogged drains and a low spot that held water for days after every storm. The membrane around the drains was separating, and the building owner was getting leaks into a storage room.
After: We cleared and repaired both drains, heat-welded new TPO membrane around each one, and installed a tapered insulation section to improve flow. Water now drains off the roof within two hours of a storm ending.
Book this service →
The flashing at the parapet wall had pulled away from the brick, letting water run behind it and into the wall assembly. The landlord noticed a musty smell in a back bedroom and a soft spot in the ceiling near the wall.
After: We removed the failed flashing, replaced the wet insulation section, and installed new flashing with proper termination and Henry Company roof cement. The musty smell cleared once the moisture source was eliminated.
Book this service →Flat roofs fail in predictable ways, and the damage they cause is rarely limited to the roof itself. Here are the problems we see most often on Union City flat roofs and how we fix them.
Ask a pro →We identify why the water is ponding, whether it is a clogged drain, a low spot in the deck, or a drainage slope issue. We clear and repair the drain, then install a tapered repair or additional drainage path so water moves off the roof instead of sitting on it.
We trace the stain back to its source using a moisture meter and infrared camera. The entry point is often 10 to 20 feet from the stain, at a seam or flashing detail. We repair the actual breach and water-test it so the stain does not return.
We clean and prep the seam, then re-weld or re-adhere it with the correct method for the membrane type. If the seam is too far gone, we install a new membrane section over the area and tie it into the existing roof with a proper lap.
We remove the failed flashing, inspect the substrate, and install new flashing with proper termination and sealant. We use roof cement and compatible membrane materials to create a continuous watertight edge.
“We had a stain spreading on our kitchen ceiling for weeks and two other roofers just wanted to patch the spot above it. Union City Roof Rescue ran a moisture meter across the whole flat roof and found the real leak at a pipe boot 15 feet away. They fixed it in an afternoon and the stain stopped growing. No more drips.”
Maria G.Homeowner, Union City Heights
✓ Verified“I manage a six-unit building and the flat roof over the rear addition was ponding after every rain. They came out, used an infrared camera to show me where the water was getting in, and repaired the seam and the drain area. That was last fall and we have not had a leak since. Fair price and they cleaned up after themselves.”
Danny R.Building Owner, Bergenline Avenue
✓ Verified“Our warehouse roof had a leak right over the inventory area. They responded the same day, tarped it to stop the water, and came back two days later to do the permanent TPO repair. The crew knew exactly what they were doing with the heat welder. Zero leaks through the rest of the season.”
Anthony P.Commercial Property Manager, Troy Towers Area
✓ VerifiedMost single-point flat roof leak repairs in Union City run $350 to $1,200 in 2026, depending on roof size, membrane type, and how much wet insulation has to be removed. A simple pipe boot or flashing repair sits at the low end. A large seam repair with insulation replacement pushes toward the higher end. We give you a fixed price after the inspection, before any work starts.
We combine three methods: a visual roof walk to check seams and flashing, a moisture meter scan to find wet areas under the membrane, and an infrared thermal camera to map where water has traveled. On larger roofs we add a roof inspection drone survey. Then we confirm the entry point with a controlled water test. Most leaks are found within an hour.
Yes, in most cases. If the membrane is structurally sound and the leak is isolated to a seam, flashing, pipe boot, or drain area, a targeted repair is the right call and costs far less than a full tear-off. Replacement only makes sense when the membrane is brittle across the whole roof or more than 25 percent of the insulation is saturated. We tell you honestly which situation you are in.
Union City Roof Rescue handles flat roof leak repair across Hudson County, including Downtown Union City, Bergenline Avenue, Palisade Avenue, and the West New York Border. Call (551) 348-9609 for same-day scheduling. We serve ZIP codes 07087 and surrounding areas, and we carry the tools and membrane materials to complete most repairs in a single visit.
Water on a flat roof does not stop on its own, and every day it sits, the damage spreads into insulation and ceiling drywall. Call Union City Roof Rescue at (551) 348-9609 for a same-day inspection. We are licensed, insured, and we carry the membrane materials to complete most repairs in one visit.
Schedule My Inspection (551) 348-9609 →Call us at (551) 348-9609 or email info@unioncityroofrescue.com. We answer the phone 24/7 for active leaks and schedule standard inspections Monday through Friday. If you leave a message after hours, we call back within the hour.